View SST34HF1601C_2037075.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

?2004 silicon storage technology, inc. s71252-00-000 3/04 1 the sst logo and superflash are registered trademarks of silicon st orage technology, inc. intel is a registered trademark of in tel corporation. csf and combomemory are trademarks of silicon storage technology, inc. these specifications are subject to change without notice. advance information features: ? flash organization: 1m x16 or 2m x8 dual-bank architecture for concurrent read/write operation ? 16 mbit: 12 mbit + 4 mbit (p)sram organization: ? 2 mbit: 128k x16 or 256k x8 ? 4 mbit: 256k x16 or 512k x8 ? 8 mbit: 512k x16 or 1024k x8 single 2.7-3.3v read and write operations superior reliability ? endurance: 100,000 cycles (typical) ? greater than 100 years data retention low power consumption: ? active current: 25 ma (typical) ? standby current: 20 a (typical) hardware sector protection (wp#) ? protects 4 outer most sectors (4 kword) in the larger bank by holding wp# low and unprotects by holding wp# high hardware reset pin (rst#) ? resets the internal state machine to reading data array byte selection for flash (ciof pin) ? selects 8-bit or 16-bit mode sector-erase capability ? uniform 2 kword sectors block-erase capability ? uniform 32 kword blocks read access time ? flash: 70 ns ? (p)sram: 70 ns erase-suspend / erase-resume capabilities security id feature ? sst: 128 bits ? user: 128 bits latched address and data fast erase and word-/byte-program (typical): ? sector-erase time: 18 ms ? block-erase time: 18 ms ? chip-erase time: 35 ms ? word-program time: 7 s automatic write timing ? internal v pp generation end-of-write detection ? toggle bit ? data# polling ? ready/busy# pin cmos i/o compatibility jedec standard command set packages available ? 56-ball lfbga (8mm x 10mm) ? 62-ball lfbga (8mm x 10mm) product description the sst34hf16x1c/d/s combomemory devices inte- grate either a 1m x16 or 2m x8 cmos flash memory bank with either a 128k x16/256k x8, 256k x16/512 x8, or 512k x16/1024k x8 cmos sram or pseudo sram (psram) memory bank in a multi-chip package (mcp). these devices are fabricated using sst?s proprietary, high-perfor- mance cmos superflash technology incorporating the split-gate cell design and thick-oxide tunneling injector to attain better reliability and manufacturability compared with alternate approaches. the sst34hf16x1c/d/s devices are ideal for applications such as cellular phones, gps devices, pdas, and other portable electronic devices in a low power and small form factor system. the sst34hf16x1c/d/s feature dual flash memory bank architecture allowing for concurrent operations between the two flash memory banks and the (p)sram. the devices can read data from either bank while an erase or program operation is in progress in the opposite bank. the two flash memory banks are partitioned into 12 mbit and 4 mbit with bottom sector protection options for storing boot code, pro- gram code, configuration/parameter data and user data. the superflash technology provides fixed erase and pro- gram times, independent of the number of erase/program cycles that have occurred. therefore, the system software or hardware does not have to be modified or de-rated as is necessary with alternative flash technologies, whose erase and program times increase with accumulated erase/pro- gram cycles. the sst34hf16x1c/d/s devices offer a guaranteed endurance of 10,000 cycles. data retention is rated at greater than 100 years. with high performance word-program, the flash memory banks provide a typical word-program time of 7 sec. the entire flash memory bank can be erased and programmed word-by-word in typ- ically 4 seconds for the sst34hf16x1c/d/s, when using interface features such as toggle bit, data# polling, or ry/ by# to indicate the completion of program operation. to 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s sst34hf168116mb csf (x8/x16) + 2/4/8 mb sram (x16) mcp combomemory
2 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 protect against inadvertent flash write, the sst34hf16x1c/d/s devices contain on-chip hardware and software data protection schemes. the flash and (p)sram operate as two independent mem- ory banks with respective bank enable signals. the mem- ory bank selection is done by two bank enable signals. the (p)sram bank enable signals, bes1# and bes2, select the (p)sram bank (bes1# and bes2 are nc for SST34HF1601C). the flash memory bank enable signal, bef#, has to be used with software data protection (sdp) command sequence when controlling the erase and pro- gram operations in the flash memory bank. the memory banks are superimposed in the same memory address space where they share common address lines, data lines, we# and oe# which minimize power consumption and area. designed, manufactured, and tested for applications requir- ing low power and small form factor, the sst34hf16x1c/ d/s are offered in both commercial and extended tempera- tures and a small footprint package to meet board space constraint requirements. see figures 3 and 4 for pin assignments. device operation the sst34hf16x1c/d/s uses bes1#, bes2 and bef# to control operation of either the flash or the (p)sram memory bank. when bef# is low, the flash bank is acti- vated for read, program or erase operation. when bes1# is low, and bes2 is high the (p)sram is activated for read and write operation. bef# and bes1# cannot be at low level, and bes2 cannot be at high level at the same time. if all bank enable signals are asserted, bus contention will result and the device may suffer permanent dam- age. all address, data, and control lines are shared by flash and (p)sram memory banks which minimizes power con- sumption and loading. the device goes into standby when bef# and bes1# bank enables are raised to v ihc (logic high) or when bef# is high and bes2 is low. concurrent read/write operation dual bank architecture of sst34hf16x1c/d/s devices allows the concurrent read/write operation whereby the user can read from one bank while programming or eras- ing in the other bank. this operation can be used when the user needs to read system code in one bank while updat- ing data in the other bank. see figures 1 and 2 for dual- bank memory organization. note: for the purposes of this table, write means to block-, sector, or chip-erase, or word-/byte-program as applicable to the appropriate bank. flash read operation the read operation of the sst34hf16x1c/d/s is con- trolled by bef# and oe#, both have to be low for the sys- tem to obtain data from the outputs. bef# is used for device selection. when bef# is high, the chip is dese- lected and only standby power is consumed. oe# is the output control and is used to gate data from the output pins. the data bus is in high impedance state when either bef# or oe# is high. refer to the read cycle timing diagram for further details (figure 8). c oncurrent r ead /w rite s tates flash (p)sram bank 1 bank 2 read write no operation write read no operation write no operation read no operation write read write no operation write no operation write write
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 3 ?2004 silicon storage technology, inc. s71252-00-000 3/04 flash word-/byte-program operation these devices are programmed on a word-by-word or byte-by-byte basis depending on the state of the ciof pin. before programming, one must ensure that the sector which is being programmed is fully erased. the program operation is accomplished in three steps: 1. software data protection is initiated using the three-byte load sequence. 2. word address and word data are loaded. during the word-program operation, the addresses are latched on the falling edge of either bef# or we#, whichever occurs last. the data is latched on the rising edge of either bef# or we#, whichever occurs first. 3. the internal program operation is initiated after the rising edge of the fourth we# or bef#, which- ever occurs first. the program operation, once ini- tiated, will be completed typically within 7 s. see figures 9 and 10 for we# and bef# controlled pro- gram operation timing diagrams and figure 22 for flow- charts. during the program operation, the only valid reads are data# polling and toggle bit. during the internal pro- gram operation, the host is free to perform additional tasks. any commands issued during an internal program opera- tion are ignored. flash sector- (block-) erase operation these devices offer both sector-erase and block-erase operations. these operations allow the system to erase the devices on a sector-by-sector (or block-by-block) basis. the sector architecture is based on a uniform sector size of 2 kword. the block-erase mode is based on a uniform block size of 32 kword. the sector-erase operation is initi- ated by executing a six-byte command sequence with a sector-erase command (30h) and sector address (sa) in the last bus cycle. the block-erase operation is initiated by executing a six-byte command sequence with block-erase command (50h) and block address (ba) in the last bus cycle. the sector or block address is latched on the falling edge of the sixth we# pulse, while the command (30h or 50h) is latched on the rising edge of the sixth we# pulse. the internal erase operation begins after the sixth we# pulse. any commands issued during the block- or sector- erase operation are ignored except erase-suspend and erase-resume. see figures 14 and 15 for timing wave- forms. flash chip-erase operation the sst34hf16x1c/d/s provide a chip-erase operation, which allows the user to erase all sectors/blocks to the ?1? state. this is useful when the device must be quickly erased. the chip-erase operation is initiated by executing a six- byte command sequence with chip-erase command (10h) at address 5555h in the last byte sequence. the erase operation begins with the rising edge of the sixth we# or bef#, whichever occurs first. during the erase operation, the only valid read is toggle bits or data# polling. see table 7 for the command sequence, figure 13 for timing diagram, and figure 26 for the flowchart. any commands issued during the chip-erase operation are ignored. when wp# is low, any attempt to chip-erase will be ignored. flash erase-suspend/ -resume operations the erase-suspend operation temporarily suspends a sector- or block-erase operation thus allowing data to be read from any memory location, or program data into any sector/block that is not suspended for an erase operation. the operation is executed by issuing a one-byte command sequence with erase-suspend command (b0h). the device automatically enters read mode within 20 s after the erase-suspend command had been issued. valid data can be read from any sector or block that is not suspended from an erase operation. reading at address location within erase-suspended sectors/blocks will output dq 2 tog- gling and dq 6 at ?1?. while in erase-suspend mode, a word-/byte-program operation is allowed except for the sector or block selected for erase-suspend. to resume sector-erase or block-erase operation which has been suspended, the system must issue an erase-resume command. the operation is executed by issuing a one-byte command sequence with erase resume command (30h) at any address in the one-byte sequence.
4 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 flash write operation status detection the sst34hf16x1c/d/s provide one hardware and two software means to detect the completion of a write (pro- gram or erase) cycle, in order to optimize the system write cycle time. the hardware detection uses the ready/busy# (ry/by#) pin. the software detection includes two status bits: data# polling (dq 7 ) and toggle bit (dq 6 ). the end-of-write detection mode is enabled after the rising edge of we#, which initiates the internal program or erase operation. the actual completion of the nonvolatile write is asynchro- nous with the system; therefore, either a ready/busy# (ry/ by#), data# polling (dq 7 ) or toggle bit (dq 6 ) read may be simultaneous with the completion of the write cycle. if this occurs, the system may possibly get an erroneous result, i.e., valid data may appear to conflict with either dq 7 or dq 6 . in order to prevent spurious rejection, if an erroneous result occurs, the software routine should include a loop to read the accessed location an additional two (2) times. if both reads are valid, then the device has completed the write cycle, otherwise the rejection is valid. ready/busy# (ry/by#) the sst34hf16x1c/d/s include a ready/busy# (ry/ by#) output signal. ry/by# is an open drain output pin that indicates whether an erase or program operation is in progress. since ry/by# is an open drain output, it allows several devices to be tied in parallel to v dd via an external pull-up resistor. after the rising edge of the final we# pulse in the command sequence, the ry/by# status is valid. when ry/by# is actively pulled low, it indicates that an erase or program operation is in progress. when ry/by# is high (ready), the devices may be read or left in standby mode. byte/word (ciof) the device includes a ciof pin to control whether the device data i/o pins operate x8 or x16. if the ciof pin is at logic ?1? (v ih ) the device is in x16 data configuration: all data i/0 pins dq 0 -dq 15 are active and controlled by bef# and oe#. if the ciof pin is at logic ?0?, the device is in x8 data config- uration: only data i/o pins dq 0 -dq 7 are active and con- trolled by bef# and oe#. the remaining data pins dq 8 - dq 14 are at hi-z, while pin dq 15 is used as the address input a -1 for the least significant bit of the address bus. flash data# polling (dq 7 ) when the devices are in an internal program operation, any attempt to read dq 7 will produce the complement of the true data. once the program operation is completed, dq 7 will produce true data. during internal erase operation, any attempt to read dq 7 will produce a ?0?. once the internal erase operation is completed, dq 7 will produce a ?1?. the data# polling is valid after the rising edge of fourth we# (or bef#) pulse for program operation. for sector-, block-, or chip-erase, the data# polling is valid after the rising edge of sixth we# (or bef#) pulse. see figure 11 for data# poll- ing (dq 7 ) timing diagram and figure 23 for a flowchart. toggle bits (dq 6 and dq 2 ) during the internal program or erase operation, any con- secutive attempts to read dq 6 will produce alternating ?1?s and ?0?s, i.e., toggling between 1 and 0. when the internal program or erase operation is completed, the dq 6 bit will stop toggling. the device is then ready for the next opera- tion. the toggle bit is valid after the rising edge of the fourth we# (or bef#) pulse for program operations. for sector-, block-, or chip-erase, the toggle bit (dq 6 ) is valid after the rising edge of sixth we# (or bef#) pulse. dq 6 will be set to ?1? if a read operation is attempted on an erase-sus- pended sector/block. if program operation is initiated in a sector/block not selected in erase-suspend mode, dq 6 will toggle. an additional toggle bit is available on dq 2 , which can be used in conjunction with dq 6 to check whether a particular sector is being actively erased or erase-suspended. table 1 shows detailed status bit information. the toggle bit (dq 2 ) is valid after the rising edge of the last we# (or bef#) pulse of a write operation. see figure 12 for toggle bit tim- ing diagram and figure 23 for a flowchart. note: dq 7, dq 6, and dq 2 require a valid address when reading status information. table 1: w rite o peration s tatus status dq 7 dq 6 dq 2 ry/by# normal operation standard program dq7# toggle no toggle 0 standard erase 0 toggle toggle 0 erase- suspend mode read from erase suspended sector/block 1 1 toggle 1 read from non-erase suspended sector/block data data data 1 program dq7# toggle n/a 0 t1.0 1252
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 5 ?2004 silicon storage technology, inc. s71252-00-000 3/04 data protection the sst34hf16x1c/d/s provide both hardware and soft- ware features to protect nonvolatile data from inadvertent writes. hardware data protection noise/glitch protection: a we# or bef# pulse of less than 5 ns will not initiate a write cycle. v dd power up/down detection: the write operation is inhibited when v dd is less than 1.5v. write inhibit mode: forcing oe# low, bef# high, or we# high will inhibit the write operation. this prevents inadvert- ent writes during power-up or power-down. hardware bloc k protection the sst34hf16x1c/d/s provide a hardware block protec- tion which protects the outermost 8 kword in bank 1. the block is protected when wp# is held low. see figures 1 and 2 for block-protection location. a user can disable block protection by driving wp# high thus allowing erase or program of data into the protected sectors. wp# must be held high prior to issuing the write command and remain stable until after the entire write operation has completed. hardware reset (rst#) the rst# pin provides a hardware method of resetting the device to read array data. when the rst# pin is held low for at least t rp, any in-progress operation will terminate and return to read mode (see figure 19). when no internal program/erase operation is in progress, a minimum period of t rhr is required after rst# is driven high before a valid read can take place (see figure 18). the erase operation that has been interrupted needs to be reinitiated after the device resumes normal operation mode to ensure data integrity. see figures 18 and 19 for timing diagrams. software data protection (sdp) the sst34hf16x1c/d/s provide the jedec standard software data protection scheme for all data alteration operations, i.e., program and erase. any program opera- tion requires the inclusion of the three-byte sequence. the three-byte load sequence is used to initiate the program operation, providing optimal protection from inadvertent write operations, e.g., during the system power-up or power-down. any erase operation requires the inclusion of six-byte sequence. the sst34hf16x1c/d/s are shipped with the software data protection permanently enabled. see table 7 for the specific software command codes. dur- ing sdp command sequence, invalid commands will abort the device to read mode within t rc. the contents of dq 15 - dq 8 are ?don?t care? during any sdp command sequence. security id the sst34hf16x1c/d/s devices offer a 256-bit security id space. the secure id space is divided into two 128-bit segments?one factory programmed segment and one user programmed segment. the first segment is pro- grammed and locked at sst with a unique, 128-bit num- ber. the user segment is left un-programmed for the customer to program as desired. to program the user seg- ment of the security id, the user must use the security id word-program command. end-of-write status is checked by reading the toggle bits. data# polling is not used for security id end-of-write detection. once programming is complete, the sec id should be locked using the user-sec- id-program-lock-out. this disables any future corruption of this space. note that regardless of whether or not the sec id is locked, neither sec id segment can be erased. the secure id space can be queried by executing a three- byte command sequence with query-sec-id command (88h) at address 5555h in the last byte sequence. to exit this mode, the exit-sec-id command should be executed. refer to table 7 for more details.
6 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 product identification the product identification mode identifies the device as the sst34hf16x1c/d/s and manufacturer as sst. this mode may be accessed by software operations only. the hardware device id read operation, which is typically used by programmers cannot be used on this device because of the shared lines between flash and (p)sram in the multi- chip package. therefore, application of high voltage to pin a 9 may damage this device. users may use the software product identification operation to identify the part (i.e., using the device id) when using multiple manufacturers in the same socket. for details, see tables 4 and 7 for soft- ware operation, figure 16 for the software id entry and read timing diagram and figure 24 for the id entry com- mand sequence flowchart. note: bk = bank address (a 19 -a 18 ) product identification mode exit in order to return to the standard read mode, the software product identification mode must be exited. exit is accom- plished by issuing the software id exit command sequence, which returns the device to the read mode. this command may also be used to reset the device to the read mode after any inadvertent transient condition that apparently causes the device to behave abnormally, e.g., not read correctly. please note that the software id exit command is ignored during an internal program or erase operation. see table 7 for software command codes, fig- ure 17 for timing waveform and figure 24 for a flowchart. (p)sram operation with bes1# low, bes2 and bef# high, the sst34hf16x1c/d/s operate as either 128k x16, 256k x16, or 512k x16 cmos (p)sram, with fully static opera- tion requiring no external clocks or timing strobes. the sst34hf16x1c/d/s (p)sram is mapped into the first 512 kword address space. when bes1#, bef# are high and bes2 is low, all memory banks are deselected and the device enters standby. read and write cycle times are equal. the control signals ubs# and lbs# provide access to the upper data byte and lower data byte (ubs# and lbs# signals are nc for sst3416x1s parts). see table 4 for x16 (p)sram read and write data byte control modes of operation. see table 5 for x8 sram read and write data byte control modes of operation. (p)sram read the (p)sram read operation of the sst34hf16x1c/d/s is controlled by oe# and bes1#, both have to be low with we# and bes2 high for the system to obtain data from the outputs. bes1# and bes2 are used for (p)sram bank selection. oe# is the output control and is used to gate data from the output pins. the data bus is in high imped- ance state when oe# is high. refer to the read cycle tim- ing diagram, figure 5, for further details. (p)sram write the (p)sram write operation of the sst34hf16x1c/d/s is controlled by we# and bes1#, both have to be low, bes2 must be high for the system to write to the (p)sram. during the word-write operation, the addresses and data are referenced to the rising edge of either bes1#, we#, or the falling edge of bes2 whichever occurs first. the write time is measured from the last falling edge of bes#1 or we# or the rising edge of bes2 to the first rising edge of bes1#, or we# or the falling edge of bes2. refer to the write cycle timing diagrams, figures 6 and 7, for further details. table 2: p roduct i dentification address data manufacturer?s id bk0000h 00bfh device id sst34hf16x1c/d/s bk0001h 734bh t2.0 1252
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 7 ?2004 silicon storage technology, inc. s71252-00-000 3/04 1252 b1.0 superflash memory (bank 1) i/o buffers superflash memory (bank 2) 2 / 4 / 8 mbit sram or psram a ms 1 - a 0 sa 5 dq 15 /a- 1 - dq 0 notes: 1. a ms = most significant address 2. for ls package only: we# = wef# and/or wes# oe# = oef# and/or oes# 3. for sst34fh16x1s, lbs# and ubs# are no connect. 4. for SST34HF1601C, bes1#, bes2, sa, lbs#, and ubs# are no connect 5. additional address for x8 sram control logic rst# bef# wp# lbs# 3 ubs# 3 we# 2 oe# 2 bes1# 4 bes2 4 ry/by# address buffers address buffers f unctional b lock d iagram
8 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 1: sst34hf16 x 1c/d, c oncurrent s uper f lash d ual -b ank m emory o rganization fffffh f8000h block 31 f7fffh f0000h block 30 effffh e8000h block 29 e7fffh e0000h block 28 dffffh d8000h block 27 d7fffh d0000h block 26 cffffh c8000h block 25 c7fffh c0000h block 24 bank 2 bffffh b8000h block 23 b7fffh b0000h block 22 affffh a8000h block 21 a7fffh a0000h block 20 9ffffh 98000h block 19 97fffh 90000h block 18 8ffffh 88000h block 17 87fffh 80000h block 16 7ffffh 78000h block 15 77fffh 70000h block 14 6ffffh 68000h block 13 67fffh 60000h block 12 5ffffh 58000h block 11 57fffh 50000h block 10 4ffffh 48000h block 9 47fffh 40000h block 8 3ffffh 38000h block 7 37fffh 30000h block 6 2ffffh 28000h block 5 27fffh 20000h block 4 1ffffh 18000h block 3 17fffh 10000h block 2 0ffffh 08000h block 1 07fffh 02000h 01fffh 00000h block 0 bank 1 bottom sector protection; 32 kword blocks; 2 kword sectors 8 kword sector protection (4-2 kword sectors) 1252 f01.0 note: the address input range in x16 mode (byte#=v ih ) is a 19 -a 0
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 9 ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 2: sst34hf16 x 1s, 2m x 8 c oncurrent s uper f lash d ual -b ank m emory o rganization 1fffffh 1f0000h block 31 1effffh 1e0000h block 30 1dffffh 1d0000h block 29 1cffffh 1c0000h block 28 1bffffh 1b0000h block 27 1affffh 1a0000h block 26 19ffffh 190000h block 25 18ffffh 180000h block 24 bank 2 17ffffh 170000h block 23 16ffffh 160000h block 22 15ffffh 150000h block 21 14ffffh 140000h block 20 13ffffh 130000h block 19 12ffffh 120000h block 18 11ffffh 110000h block 17 10ffffh 100000h block 16 0fffffh 0f0000h block 15 0effffh 0e0000h block 14 0dffffh 0d0000h block 13 0cffffh 0c0000h block 12 0bffffh 0b0000h block 11 0affffh 0a0000h block 10 09ffffh 090000h block 9 08ffffh 080000h block 8 07ffffh 070000h block 7 06ffffh 060000h block 6 05ffffh 050000h block 5 04ffffh 040000h block 4 03ffffh 030000h block 3 02ffffh 020000h block 2 01ffffh 010000h block 1 00ffffh 004000h 003fffh 000000h block 0 bank 1 bottom sector protection; 64 kbyte blocks; 4 kbyte sectors 16 kbyte sector protection (4-4 kbyte sectors) 1252 f01b.0 note: the address input range in x8 mode (byte#=v il ) is a 19 -a -1
10 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 3: p in a ssignments for 56- ball lfbga (8 mm x 10 mm ) figure 4: p in a ssignments for 62- ball lfbga (8 mm x 10 mm ) 1252 56-lfbga p1a.0 a11 a8 we# wp# lbs# a7 a15 a12 a19 bes2 rst# ubs# a6 a3 nc a13 a9 nc ry/by# a18 a5 a2 nc a14 a10 a17 a4 a1 a16 nc dq6 dq1 v ss a0 ciof note* dq13 dq4 dq3 dq9 oe# bef# v ss dq7 dq12 v dds v ddf dq10 dq0 bes1# dq14 dq5 nc dq11 dq2 dq8 a b c d e f g h 8 7 6 5 4 3 2 1 top view (balls facing down) note* = dq 15 /a -1 1252 56-lfbga p1b.0 a11 a8 we# wp# nc a7 a15 a12 a19 bes2 rst# nc a6 a3 nc a13 a9 nc ry/by# a18 a5 a2 nc a14 a10 a17 a4 a1 a16 sa dq6 dq1 v ss a0 ciof note* dq13 dq4 dq3 dq9 oe# bef# v ss dq7 dq12 v dds v ddf dq10 dq0 bes1# dq14 dq5 nc dq11 dq2 dq8 a b c d e f g h 8 7 6 5 4 3 2 1 top view (balls facing down) note* = dq 15 /a -1 sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d sst34hf1621s / sst34hf1641s note: 1. for SST34HF1601C, v dds, sa, bes2, and bes1# are no connect. 1252 62-lfbga p2.0 nc nc nc a16 wef# v sss wp# lbs# a18 nc a11 a8 ry/by# rst# nc ubs# a17 a5 a15 a10 a19 oes# a7 a4 a14 a9 dq11 a6 a0 a13 dq15 dq13 dq12 dq9 a3 bef# a12 wes# dq6 bes2 dq10 dq8 a2 v ssf v ssf dq14 dq4 v dds dq2 dq0 a1 oef# nc dq7 dq5 v ddf dq3 dq1 bes1# nc nc nc a b c d e f g h j k 8 7 6 5 4 3 2 1 top view (balls facing down) note: 1. for SST34HF1601C, v sss , v dds , wes#, bes2, oes#, ubs#, lbs#, and bes1# are no connect. sst34hf16x1c/d
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 11 ?2004 silicon storage technology, inc. s71252-00-000 3/04 table 3: p in d escription symbol pin name functions a ms 1 to a 0 address inputs to provide flash address, a 19 -a 0 . to provide (p)sram address, a ms -a 0 sa sram x8 address to provide additional address for x8 sram dq 14 -dq 0 data inputs/outputs to output data during read cycles and receive input data during write cycles. data is internally latched during a flash erase/program cycle. the outputs are in tri-state when oe# is high or bes1# is high or bes2 is low and bef# is high. dq 15 /a -1 data input/output and lbs address dq 15 is used as data i/o pin when in x16 mode (ciof = ?1?) a -1 is used as the lbs address pin when in x8 mode (ciof = ?0?) bef# flash memory bank enable to activate the flash memory bank when bef# is low bes1# (p)sram memory bank enable to activate the (p)sram memory bank when bes1# is low bes2 (p)sram memory bank enable to activate the (p)sram memory bank when bes2 is high oef# 2 output enable to gate the data output buffers for flash 2 only oes# 2 output enable to gate the data output buffers for sram 2 only wef# 2 write enable to control the write operations for flash 2 only wes# 2 write enable to control the write operations for sram 2 only oe# output enable to gate the data output buffers we# write enable to control the write operations ciof byte selection for flash when low, select byte mode. when high, select word mode. ubs# upper byte control ((p)sram) to enable dq 15 -dq 8 lbs# lower byte control ((p)sram) to enable dq 7 -dq 0 wp# write protect to protect and unprotect the bottom 8 kword (4 sectors) from erase or program operation rst# reset to reset and return the device to read mode ry/by# ready/busy# to output the status of a program or erase operation ry/by# is a open drain output, so a 10k ? - 100k ? pull-up resistor is required to allow ry/by# to transition high indicating the device is ready to read. v ssf 2 ground flash 2 only v sss 2 ground sram 2 only v ss ground v dd f power supply (flash) 2.7-3.3v power supply to flash only v dd s power supply ((p)sram) 2.7-3.3v power supply to (p)sram only nc no connection unconnected pins t3.0 1252 1. a ms = most significant address a ms = a 16 for sst34hf1621c/d/s, a 17 for sst34hf1641c/d/s, and a 18 for sst34hf1681c/d/s 2. ls package only
12 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 table 4: o perational m odes s election for x 16 (p)sram mode bef# 1 bes1# 1,2 bes2 1,2 oe# 2,3 we# 2,3 lbs# 2 ubs# 2 dq 15-8 dq 7-0 ciof = v ih ciof = v il full standby v ih v ih x x x x x high-z high-z high-z xv il xxxx output disable v ih v il v ih v ih v ih x x high-z high-z high-z v il v ih xxv ih v ih v il v ih xv ih v ih x x high-z high-z high-z xv il flash read v il v ih xv il v ih xxd out d out dq 14-8 = high-z dq 15 = a -1 xv il flash write v il v ih x v ih v il xxd in d in dq 14-8 = high-z dq 15 = a -1 xv il flash erase v il v ih xv ih v il xx x x x xv il (p)sram read v ih v il v ih v il v ih v il v il d out d out d out v ih v il high-z d out d out v il v ih d out high-z high-z (p)sram write v ih v il v ih xv il v il v il d in d in d in v ih v il high-z d in d in v il v ih d in high-z high-z product identification 4 v il v ih v il v il v ih x x manufacturer?s id 5 device id 5 t4.0 1252 1. do not apply bef# = v il , bes1# = v il and bes2 = v ih at the same time 2. x can be v il or v ih, but no other value. 3. oe# = oef# and oes# we# = wef# and wes# for ls package only 4. software mode only 5. with a 19 -a 18 = v il; sst manufacturer?s id = bfh, is read with a 0 =0, sst34hf16x1c/d/s device id = 734bh, is read with a 0 =1
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 13 ?2004 silicon storage technology, inc. s71252-00-000 3/04 table 5: o perational m odes s election for x 8 sram mode bef# 1 bes1# 1,2 bes2 1,2 oe# 2 we# 2 sa 2 dq 15-8 dq 7-0 ciof = v ih ciof = v il full standby v ih v ih x x x x high-z high-z high-z xv il xxx output disable v ih v il v ih v ih v ih x high-z high-z high-z v il v ih xxv ih v il v ih xv ih v ih x high-z high-z high-z xv il flash read v il v ih xv il v ih xd out d out dq 14-8 = high-z dq 15 = a -1 xv il flash write v il v ih x v ih v il xd in d in dq 14-8 = high-z dq 15 = a -1 xv il flash erase v il v ih xv ih v il xx x x xv il sram read v ih v il v ih v il v ih sa d out high-z high-z sram write v ih v il v ih xv il sa d in high-z high-z product identification 3 v il v ih v il v il v ih x manufacturer?s id 4 device id 4 manufacturer?s id 4 device id 4 t5.0 1252 1. do not apply bef# = v il , bes1# = v il and bes2 = v ih at the same time 2. x can be v il or v ih , but no other value. 3. software mode only 4. with a 19 -a 18 = v il; sst manufacturer?s id = bfh, is read with a 0 =0, sst34hf16x1c/d/s device id = 734bh, is read with a 0 =1, for x8 a -1 will not be part of the device id table 6: o perational m odes s election for 0 m bit sram: SST34HF1601C mode bef# oe# 1 , 2 1. x can be v il or v ih , but no other value. 2. oe# = oef#, we# = wef# we# 1,2 dq 15-8 dq 7-0 ciof = v ih ciof = v il full standby v ih x x high-z high-z high-z xx output disable v ih v ih v ih high-z high-z high-z xx v il v ih v ih high-z high-z high-z flash read v il v il v ih d out d out dq 14-8 = high-z dq 15 = a -1 flash write v il v ih v il d in d in dq 14-8 = high-z dq 15 = a -1 flash erase v il v ih v il xxx product identification 3 3. software mode only v il v il v ih manufacturer?s id 4 device id 4 4. with a 19 -a 18 = v il; sst manufacturer?s id = bfh, is read with a 0 =0, SST34HF1601C device id = 734bh, is read with a 0 =1, for x8 a -1 will not be part of the device id manufacturer?s id 4 device id 4 t6.0 1252
14 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 table 7: s oftware c ommand s equence command sequence 1st bus write cycle 2nd bus write cycle 3rd bus write cycle 4th bus write cycle 5th bus write cycle 6th bus write cycle addr 1 data 2 addr 1 data 2 addr 1 data 2 addr 1 data 2 addr 1 data 2 addr 1 data 2 word-/byte-program 5555h aah 2aaah 55h 5555h a0h wa 3 data sector-erase 5555h aah 2aaah 55h 5555h 80h 5555h aah 2aaah 55h sa x 4 30h block-erase 5555h aah 2aaah 55h 5555h 80h 5555h aah 2aaah 55h ba x 4 50h chip-erase 5555h aah 2aaah 55h 5555h 80h 5555h aah 2aaah 55h 5555h 10h erase-suspend xxxxh b0h erase-resume xxxxh 30h query sec id 5 5555h aah 2aaah 55h 5555h 88h user security id word-/byte-program 5555h aah 2aaah 55h 5555h a5h siwa 6 data user security id program lock-out 7 5555h aah 2aaah 55h 5555h 85h xxh 0000h software id entry 8 5555h aah 2aaah 55h bk x 9 5555h 90h software id exit/ sec id exit 10,11 5555h aah 2aaah 55h 5555h f0h software id exit/ sec id exit 10,11 xxh f0h t7.0 1252 1. address format a 14 -a 0 (hex), addresses a 19 -a 15 can be v il or v ih , but no other value, for the command sequence when in x16 mode. when in x8 mode, addresses a 19 -a 15, address a -1 and dq 14 -dq 8 can be v il or v ih , but no other value, for the command sequence. 2. dq 15 -dq 8 can be v il or v ih , but no other value, for the command sequence 3. wa = program word/byte address 4. sa x for sector-erase; uses a 19 -a 10 address lines ba x for block-erase; uses a 19 -a 15 address lines 5. for sst34hf16x1c/d/s, sst id is read with a 3 = 0 (address range = 00000h to 00007h), user id is read with a 3 = 1 (address range = 00010h to 00017h). lock status is read with a 7 -a 0 = 000ffh. unlocked: dq 3 = 1 / locked: dq 3 = 0. 6. siwa = user security id program word/byte address for sst34hf16x1c/d/s, valid word-addresses for user sec id are from 00010h-00017h. all 4 cycles of user security id word-program and program lock-out must be completed before going back to read-array mode. 7. the user security id program lock-out command must be executed in x16 mode (byte#=v ih ). 8. the device does not remain in software product identification mode if powered down. 9. a 19 and a 18 = v il 10. both software id exit operations are equivalent 11. if users never lock after programming, user sec id can be programmed over the pr eviously unprogrammed bi ts (data=1) using th e user sec id mode again (the programmed ?0? bits cannot be reversed to ?1?). for sst34hf16x1c/d/s, valid word-addresses for user sec id are from 00010h-00017h.
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 15 ?2004 silicon storage technology, inc. s71252-00-000 3/04 absolute maximum stress ratings (applied conditions greater than those listed under ?absolute maximum stress ratings? may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. exposure to absolute maximum stress rating conditions may affect device reliability.) operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20c to +85c storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65c to +125c d. c. voltage on any pin to ground potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.5v to v dd 1 +0.3v transient voltage (<20 ns) on any pin to ground potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1.0v to v dd 1 +1.0v package power dissipation capability (ta = 25c) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0w output short circuit current 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 ma 1. v dd = v ddf and v dds 2. outputs shorted for no more than one second. no more than one output shorted at a time. o perating r ange range ambient temp v dd commercial 0c to +70c 2.7-3.3v extended -20c to +85c 2.7-3.3v ac c onditions of t est input rise/fall time . . . . . . . . . . . . . . 5 ns output load . . . . . . . . . . . . . . . . . . . . c l = 30 pf see figures 20 and 21
16 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 table 8: dc o perating c haracteristics (v dd = v ddf and v dds = 2.7-3.3v) symbol parameter limits test conditions min max units i dd 1 active v dd current address input = v ilt /v iht, at f=1/t rc min, v dd =v dd max, all dqs open read oe#=v il , we#=v ih flash 35 ma bef#=v il , bes1#=v ih , or bes2=v il (p)sram 30 ma bef#=v ih , bes1#=v il , bes2=v ih concurrent operation 60 ma bef#=v ih , bes1#=v il , bes2=v ih write 2 we#=v il flash 40 ma bef#=v il , bes1#=v ih , or bes2=v il , oe#=v ih (p)sram 30 ma bef#=v ih , bes1#=v il , bes2=v ih i sb standby v dd current sram psram 30 85 a a v dd = v dd max, bef#=bes1#=v ihc , bes2=v ilc i rt reset v dd current 30 a rst#=gnd i li input leakage current 1 a v in =gnd to v dd , v dd =v dd max i liw input leakage current on wp# pin and rst# pin 10 a wp#=gnd to v dd , v dd =v dd max rst#=gnd to v dd , v dd =v dd max i lo output leakage current 10 a v out =gnd to v dd , v dd =v dd max v il input low voltage 0.8 v v dd =v dd min v ilc input low voltage (cmos) 0.3 v v dd =v dd max v ih input high voltage 0.7 v dd vv dd =v dd max v ihc input high voltage (cmos) v dd -0.3 v v dd =v dd max v olf flash output low voltage 0.2 v i ol =100 a, v dd =v dd min v ohf flash output high voltage v dd -0.2 v i oh =-100 a, v dd =v dd min v ols (p)sram output low voltage 0.4 v iol =1 ma, v dd =v dd min v ohs (p)sram output high voltage 2.2 v ioh =-500 a, v dd =v dd min t8.0 1252 1. address input = v ilt /v iht, v dd =v dd max (see figure 20) 2. i dd active while erase or program is in progress.
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 17 ?2004 silicon storage technology, inc. s71252-00-000 3/04 table 9: r ecommended s ystem p ower - up t imings symbol parameter minimum units t pu-read 1 power-up to read operation 100 s t pu-write 1 power-up to write operation 100 s t9.0 1252 1. this parameter is measured only for init ial qualification and after a design or proces s change that could affect this paramet er. table 10: c apacitance (ta = 25c, f=1 mhz, other pins open) parameter description test condition maximum c i/o 1 1. this parameter is measured only for init ial qualification and after a design or proces s change that could affect this paramet er. i/o pin capacitance v i/o = 0v 20 pf c in 1 input capacitance v in = 0v 16 pf t10.0 1252 table 11: f lash r eliability c haracteristics symbol parameter minimum specification units test method n end 1 1. this parameter is measured only for init ial qualification and after a design or proces s change that could affect this paramet er. endurance 10,000 cycles jedec standard a117 t dr 1 data retention 100 years jedec standard a103 i lt h 1 latch up 100 + i dd ma jedec standard 78 t11.0 1252
18 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 ac characteristics table 12: (p)sram r ead c ycle t iming p arameters min max units t rcs read cycle time 70 ns t aas address access time 70 ns t bes bank enable access time 70 ns t oes output enable access time 35 ns t byes ubs#, lbs# access time 70 ns t blzs 1 1. this parameter is measured only for init ial qualification and after a design or proces s change that could affect this paramet er. bes# to active output 0 ns t olzs 1 output enable to active output 0 ns t bylzs 1 ubs#, lbs# to active output 0 ns t bhzs 1 bes# to high-z output 25 ns t ohzs 1 output disable to high-z output 25 ns t byhzs 1 ubs#, lbs# to high-z output 35 ns t ohs output hold from address change 10 ns t12.0 1252 table 13: (p)sram w rite c ycle t iming p arameters symbol parameter min max units t wcs write cycle time 70 ns t bws bank enable to end-of-write 60 ns t aws address valid to end-of-write 60 ns t asts address set-up time 0 ns t wps write pulse width 60 ns t wrs write recovery time 0 ns t byws ubs#, lbs# to end-of-write 60 ns t odws output disable from we# low 30 ns t oews output enable from we# high 0 ns t dss data set-up time 30 ns t dhs data hold from write time 0 ns t13.0 1252
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 19 ?2004 silicon storage technology, inc. s71252-00-000 3/04 table 14: f lash r ead c ycle t iming p arameters v dd = 2.7-3.3v symbol parameter min max units t rc read cycle time 70 ns t ce chip enable access time 70 ns t aa address access time 70 ns t oe output enable access time 35 ns t clz 1 bef# low to active output 0 ns t olz 1 oe# low to active output 0 ns t chz 1 bef# high to high-z output 20 ns t ohz 1 oe# high to high-z output 20 ns t oh 1 output hold from address change 0 ns t rp 1 rst# pulse width 500 ns t rhr 1 rst# high before read 50 ns t ry 1,2 rst# pin low to read 20 s t14.0 1252 1. this parameter is measured only for init ial qualification and after the design or pr ocess change that could affect this param eter. 2. this parameter applies to sector-erase , block-erase and program operations. this parameter does not apply to chip-erase. table 15: f lash p rogram /e rase c ycle t iming p arameters symbol parameter min max units t bp word-program time 10 s t as address setup time 0 ns t ah address hold time 40 ns t cs we# and bef# setup time 0 ns t ch we# and bef# hold time 0 ns t oes oe# high setup time 0 ns t oeh oe# high hold time 10 ns t cp bef# pulse width 40 ns t wp we# pulse width 40 ns t wph 1 1. this parameter is measured only for init ial qualification and after a design or proces s change that could affect this paramet er. we# pulse width high 30 ns t cph 1 bef# pulse width high 30 ns t ds data setup time 30 ns t dh 1 data hold time 0 ns t ida 1 software id access and exit time 150 ns t es erase-suspend latency 20 s t by 1,2 2. this parameter applies to sector-era se, block-erase, and program operations. this parameter does not apply to chip-erase operations. ry/by# delay time 90 ns t br 1 bus# recovery time 1s t se sector-erase 25 ms t be block-erase 25 ms t sce chip-erase 50 ms t15.0 1252
20 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 5: (p)sram r ead c ycle t iming d iagram figure 6: (p)sram w rite c ycle t iming d iagram (we# c ontrolled ) 1 addresses a mss-0 dq 15-0 ubs#, lbs# oe# bes1# bes2 t rcs t aas t bes t oes t blzs t olzs t byes t bylzs t byhzs data valid t ohzs t bhzs t ohs 1252 f04.0 t bes note: a mss = most significant address a mss = a 16 for sst34hf1621c/s, a 17 for sst34hf1641c/d/s, and a 18 for sst34hf1681d for sst34hf16x1s, lbs# and ubs# are no connect and in x8 mode, the additional sram address is sa t aws addresses a mss 3 -0 bes1# bes2 we# ubs#, lbs# t wps t wrs t wcs t asts t bws t bws t byws t odws t oews t dss t dhs 1252 f05.0 note 2 note 2 dq 15-8, dq 7-0 valid data in note: 1. if oe# is high during the write cycle, the outputs will remain at high impedance. 2. if bes1# goes low or bes2 goes high coincident with or af ter we# goes low, the output will remain at high impedance. if bes1# goes high or bes2 goes low coincident with or before we# goes high, the output will remain at high impedance. because d in signals may be in the output state at this time, input signals of reverse polarity must not be applied. 3. a mss = most significant sram address a mss = a 16 for sst34hf1621c/s, a 17 for sst34hf1641c/d/s, and a 18 for sst34hf1681d for sst34hf16x1s, lbs# and ubs# are no connect and in x8 mode, the additional sram address is sa
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 21 ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 7: (p)sram w rite c ycle t iming d iagram (ubs#, lbs# c ontrolled ) 1 x 16 (p)sram only addresses a mss 3 -0 we# bes1# bes2 t bws t bws t aws t wcs t wps t wrs t asts t byws dq 15-8, dq 7-0 valid data in note 2 note 2 t dss t dhs ubs#, lbs# 1252 f06.0 note: 1. if oe# is high during the write cycle, the outputs will remain at high impedance. 2. because d in signals may be in the output state at this time, input signals of reverse polarity must not be applied. 3. a mss = most significant sram address a mss = a 16 for sst34hf1621c, a 17 for sst34hf1641c/d, and a 18 for sst34hf1681d
22 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 8: f lash r ead c ycle t iming d iagram for w ord m ode (f or b yte m ode a -1 = a ddress i nput ) figure 9: f lash we# c ontrolled w ord -p rogram c ycle t iming d iagram for w ord m ode (f or b yte m ode a -1 = a ddress i nput ) 1252 f07.0 address a 19-0 dq 15-0 we# oe# bef# t ce t rc t aa t oe t olz v ih high-z t clz t oh t chz high-z data valid data valid t ohz 1252 f08.0 address a 19-0 dq 15-0 t dh t wph t ds t wp t ah t as t ch t cs t by bef# ry/by# 5555 2aaa 5555 addr xxaa xx55 xxa0 data word (addr/data) oe# we# t br t bp note: x can be v il or v ih , but no other value. valid
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 23 ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 10: f lash bef# c ontrolled w ord -p rogram c ycle t iming d iagram for w ord m ode (f or b yte m ode a -1 = a ddress i nput ) figure 11: f lash d ata # p olling t iming d iagram for w ord m ode (f or b yte m ode a -1 = a ddress i nput ) valid 1252 f09.0 address a 19-0 dq 15-0 t dh t cph t ds t cp t ah t as t ch t cs we# 5555 2aaa 5555 addr xxaa xx55 xxa0 data word (addr/data) oe# bef# t bp t by ry/by# t br note: x can be v il or v ih , but no other value. 1252 f10.0 address a 19-0 dq 7 data data# data# data we# oe# bef# t oeh t oe t ce t oes ry/by# t by
24 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 12: f lash t oggle b it t iming d iagram for w ord m ode (f or b yte m ode a -1 = d on ? t c are ) figure 13: f lash we# c ontrolled c hip -e rase t iming d iagram for w ord m ode (f or b yte m ode a -1 = d on ? t c are ) 1252 f11.0 address a 19-0 dq 6 we# oe# bef# t oe t oeh t ce two read cycles with same outputs valid data t br valid t br 1252 f12.0 address a 19-0 dq 15-0 we# 5555 2aaa 2aaa 5555 5555 xx55 xx10 xx55 xxaa xx80 xxaa 5555 oe# bef# six-byte code for chip-erase t sce t wp t by ry/by# note: this device also supports bef# controlled chip-erase operation. the we# and bef# signals are interchangeable as long as minimum timings are meet. (see table 15.) x can be v il or v ih, but no other value.
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 25 ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 14: f lash we# c ontrolled b lock -e rase t iming d iagram for w ord m ode (f or b yte m ode a -1 = d on ? t c are ) figure 15: f lash we# c ontrolled s ector -e rase t iming d iagram for w ord m ode (f or b yte m ode a -1 = d on ? t c are ) 1252 f13.0 address a 19-0 dq 15-0 we# 5555 2aaa 2aaa 5555 5555 xx55 xx50 xx55 xxaa xx80 xxaa ba x oe# bef# six-byte code for block-erase t wp t by ry/by# valid t br t be note: this device also supports bef# controlled block-erase operation. the we# and bef# signals are interchangeable as long as minimum timings are meet. (see table 15.) ba x = block address x can be v il or v ih, but no other value. 1252 f14.0 address a 19-0 dq 15-0 we# 5555 2aaa 2aaa 5555 5555 xx55 xx30 xx55 xxaa xx80 xxaa sa x oe# bef# six-byte code for sector-erase t wp t by ry/by# valid t br t se note: this device also supports bef# controlled sector-erase operation. the we# and bef# signals are interchangeable as long as minimum timings are meet. (see table 15.) sa x = sector address x can be v il or v ih, but no other value.
26 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 16: f lash s oftware id e ntry and r ead for w ord m ode (f or b yte m ode a -1 = 0) figure 17: f lash s oftware id e xit for w ord m ode (f or b yte m ode a -1 = 0) 1252 f15.0 address a 14-0 t ida dq 15-0 we# 5555 2aaa 5555 0000 0001 oe# bef# three-byte sequence for software id entry t wp t wph t aa 00bf device id xx55 xxaa xx90 note: x can be v il or v ih, but no other value. device id - 734bh for sst34hf16x1c/ds 1252 f16.0 address a 14-0 dq 15-0 t ida t wp t whp we# 5555 2aaa 5555 three-byte sequence for software id exit and reset oe# bef# xxaa xx55 xxf0 note: x can be v il or v ih , but no other value
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 27 ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 18: rst# t iming ( when no internal operation is in progress ) figure 19: rst# t iming ( during s ector - or b lock -e rase operation ) 1252 f17.0 ry/by# 0v rst# bef#/oe# t rp t rhr 1252 f18.0 ry/by# bef# oe# t rp t ry t br rst#
28 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 20: ac i nput /o utput r eference w aveforms figure 21: a t est l oad e xample 1252 f19.0 reference points output input v it v iht v ilt v ot ac test inputs are driven at v iht (0.9 v dd ) for a logic ?1? and v ilt (0.1 v dd ) for a logic ?0?. measurement reference points for inputs and outputs are v it (0.5 v dd ) and v ot (0.5 v dd ). input rise and fall times (10% ? 90%) are <5 ns. note: v it - v input te s t v ot - v output te s t v iht - v input high test v ilt - v input low test 1252 f20.0 to tester to dut c l
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 29 ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 22: w ord -p rogram a lgorithm 1252 f21.0 start load data: xxaah address: 5555h load data: xx55h address: 2aaah load data: xxa0h address: 5555h load word address/word data wait for end of program (t bp , data# polling bit, or toggle bit operation) program completed note: x can be v il or v ih , but no other value.
30 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 23: w ait o ptions 1252 f22.0 wait t bp , t sce, t se or t be program/erase initiated internal timer toggle bit ye s ye s no no program/erase completed does dq 6 match? read same word data# polling program/erase completed program/erase completed read word is dq 7 = true data? read dq 7 program/erase initiated program/erase initiated
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 31 ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 24: s oftware p roduct id c ommand f lowcharts 1252 f23.0 load data: xxaah address: 5555h software product id entry command sequence load data: xx55h address: 2aaah load data: xx90h address: 5555h wait t ida read software id load data: xxaah address: 5555h software id exit command sequence load data: xx55h address: 2aaah load data: xxf0h address: 5555h wait t ida return to normal operation note: x can be v il or v ih, but no other value.
32 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 25: s oftware s ec id c ommand f lowcharts 1252 f24.0 sec id exit command sequence load data: xxf0h address: xxh return to normal operation wait t ida x can be v il or v ih, but no other value load data: xxaah address: 5555h sec id query entry command sequence load data: xx55h address: 2aaah load data: xx88h address: 5555h wait t ida read sec id load data: xxaah address: 5555h load data: xx55h address: 2aaah load data: xxf0h address: 5555h wait t ida return to normal operation
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 33 ?2004 silicon storage technology, inc. s71252-00-000 3/04 figure 26: e rase c ommand s equence 1252 f25.0 load data: xxaah address: 5555h chip-erase command sequence load data: xx55h address: 2aaah load data: xx80h address: 5555h load data: xx55h address: 2aaah load data: xx10h address: 5555h load data: xxaah address: 5555h wait t sce chip erased to ffffh load data: xxaah address: 5555h sector-erase command sequence load data: xx55h address: 2aaah load data: xx80h address: 5555h load data: xx55h address: 2aaah load data: xx30h address: sa x load data: xxaah address: 5555h wait t se sector erased to ffffh load data: xxaah address: 5555h block-erase command sequence load data: xx55h address: 2aaah load data: xx80h address: 5555h load data: xx55h address: 2aaah load data: xx50h address: ba x load data: xxaah address: 5555h wait t be block erased to ffffh note: x can be v il or v ih, but no other value.
34 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 product ordering information package attribute e = non-pb package modifier p = 56 balls s = 62 balls package type l1 = lfbga (8mm x 10mm x 1.4mm, 0.45mm ball size) l = lfbga (8mm x 10mm x 1.4mm, 0.40mm ball size) b1 = tfbga (8mm x 10mm x 1.2mm, 0.45mm ball size) temperature range c = commercial = 0c to +70c e = extended = -20c to +85c minimum endurance 4 =10,000 cycles read access speed 70 = 70 ns version c = x16 mbit sram d = x16 mbit psram s = x8 mbit sram bank split 1 = 12 mbit + 4 mbit sram density 0 = no sram 2 = 2 mbit 4 = 4 mbit 8 = 8 mbit flash density 16 = 16 mbit voltage h = 2.7-3.3v product series 34 = concurrent superflash + sram combomemory device speed suffix1 suffix2 sst34 h f16x 1 x -xxx -x x -xx x x
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 35 ?2004 silicon storage technology, inc. s71252-00-000 3/04 valid combinations for SST34HF1601C SST34HF1601C-70-4c-l1p SST34HF1601C-70-4c-ls SST34HF1601C-70-4c-b1p SST34HF1601C-70-4c-l1pe SST34HF1601C-70-4c-lse SST34HF1601C-70-4c-b1pe SST34HF1601C-70-4e-l1p SST34HF1601C-70-4e-ls SST34HF1601C-70-4e-b1p SST34HF1601C-70-4e-l1pe SST34HF1601C-70-4e-lse SST34HF1601C-70-4e-b1pe valid combinations for sst34hf1621c sst34hf1621c-70-4c-l1p sst34hf1621c-70-4c-ls sst34hf1621c-70-4c-l1pe sst34hf1621c-70-4c-lse sst34hf1621c-70-4e-l1p sst34hf1621c-70-4e-ls sst34hf1621c-70-4e-l1pe sst34hf1621c-70-4e-lse valid combinations for sst34hf1621s sst34hf1621s-70-4c-l1p sst34hf1621s-70-4c-l1pe sst34hf1621s-70-4e-l1p sst34hf1621s-70-4e-l1pe valid combinations for sst34hf1641c sst34hf1641c-70-4c-l1p sst34hf1641c-70-4c-ls sst34hf1641c-70-4c-l1pe sst34hf1641c-70-4c-lse sst34hf1641c-70-4e-l1p sst34hf1641c-70-4e-ls sst34hf1641c-70-4e-l1pe sst34hf1641c-70-4e-lse valid combinations for sst34hf1641d sst34hf1641d-70-4c-l1p sst34hf1641d-70-4c-ls sst34hf1641d-70-4c-l1pe sst34hf1641d-70-4c-lse sst34hf1641d-70-4e-l1p sst34hf1641d-70-4e-ls sst34hf1641d-70-4e-l1pe sst34hf1641d-70-4e-lse valid combinations for sst34hf1641s sst34hf1641s-70-4c-l1p sst34hf1641s-70-4c-l1pe sst34hf1641s-70-4e-l1p sst34hf1641s-70-4e-l1pe valid combinations for sst34hf1681d sst34hf1681d-70-4c-l1p sst34hf1681d-70-4c-ls sst34hf1681d-70-4c-l1pe sst34hf1681d-70-4c-lse sst34hf1681d-70-4e-l1p sst34hf1681d-70-4e-ls sst34hf1681d-70-4e-l1pe sst34hf1681d-70-4e-lse note: valid combinations are those products in mass production or will be in mass production. consult your sst sales representative to confirm availability of valid combinations and to determine availability of new combinations.
36 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 packaging diagrams 56- ball l ow - profile , f ine - pitch b all g rid a rray (lfbga) 8 mm x 10 mm sst p ackage c ode : l1p a1 corner h g f e d c b a a b c d e f g h bottom view top view side view 8 7 6 5 4 3 2 1 seating plane 0.35 0.05 1.30 0.10 0.12 8.00 0.20 0.45 0.05 (56x) a1 corner 10.00 0.20 0.80 5.60 0.80 5.60 56-lfbga-l1p-8x10-450mic-3 note: 1. although many dimensions are similar to those of jedec publication 95, mo-210, this specific package is not registered. 2. all linear dimensions are in millimeters. 3. coplanarity: 0.12 mm 4. the actual shape of the corners may be slightly different than as portrayed in the drawing. 8 7 6 5 4 3 2 1 1mm
advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s 37 ?2004 silicon storage technology, inc. s71252-00-000 3/04 62- ball l ow - profile , f ine - pitch b all g rid a rray (lfbga) 8 mm x 10 mm sst p ackage c ode : ls a1 corner k j h g f e d c b a a b c d e f g h j k bottom view top view 8 7 6 5 4 3 2 1 8.00 0.20 0.40 0.05 (62x) a1 corner 10.00 0.20 0.80 5.60 0.80 7.20 62-lfbga-ls-8x10-400mic-3 note: 1. although many dimensions are similar to those of jedec publication 95, mo-210, this specific package is not registered. 2. all linear dimensions are in millimeters. 3. coplanarity: 0.12 mm 4. the actual shape of the corners may be slightly different than as portrayed in the drawing. 8 7 6 5 4 3 2 1 1mm side view seating plane 0.32 0.05 1.30 0.10 0.12
38 advance information 16 mbit concurrent superflash + 2/4/8 mbit sram combomemory SST34HF1601C / sst34hf1621c / sst34hf1641c sst34hf1641d / sst34hf1681d / sst34hf1621s / sst34hf1641s ?2004 silicon storage technology, inc. s71252-00-000 3/04 56- ball t hin - profile , f ine - pitch b all g rid a rray (tfbga) 8 mm x 10 mm sst p ackage c ode : b1p table 16: r evision h istory number description date 00 initial release mar 2004 1.2 max h g f e d c b a a b c d e f g h bottom view top view side view 8 7 6 5 4 3 2 1 seating plane 0.35 0.05 0.12 8.00 0.20 0.45 0.05 (56x) 10.00 0.20 0.80 5.60 0.80 5.60 56-tfbga-b1p-8x10-450mic-1 note: 1. although many dimensions are similar to those of jedec publication 95, mo-210, this specific package is not registere d. 2. all linear dimensions are in millimeters. 3. coplanarity: 0.12 mm 4. ball opening size is 0.38 mm ( 0.05 mm) 8 7 6 5 4 3 2 1 1mm a1 corner a1 corner silicon storage technology, inc. 1171 sonora court sunnyvale, ca 94086 telephone 408-735-9110 fax 408-735-9036 www.superflash.com or www.sst.com

▲Up To Search▲

Price & Availability of SST34HF1601C

	To Download SST34HF1601C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .